marshal — Internal Python object serialization


This module contains functions that can read and write Python values in a binary format. The format is specific to Python, but independent of machine architecture issues (e.g., you can write a Python value to a file on a PC, transport the file to a Sun, and read it back there). Details of the format are undocumented on purpose; it may change between Python versions (although it rarely does). [1]

This is not a general “persistence” module. For general persistence and transfer of Python objects through RPC calls, see the modules pickle and shelve. The marshal module exists mainly to support reading and writing the “pseudo-compiled” code for Python modules of .pyc files. Therefore, the Python maintainers reserve the right to modify the marshal format in backward incompatible ways should the need arise. The format of code objects is not compatible between Python versions, even if the version of the format is the same. De-serializing a code object in the incorrect Python version has undefined behavior. If you’re serializing and de-serializing Python objects, use the pickle module instead – the performance is comparable, version independence is guaranteed, and pickle supports a substantially wider range of objects than marshal.

Warning

The marshal module is not intended to be secure against erroneous or maliciously constructed data. Never unmarshal data received from an untrusted or unauthenticated source.

Not all Python object types are supported; in general, only objects whose value is independent from a particular invocation of Python can be written and read by this module. The following types are supported: booleans, integers, floating point numbers, complex numbers, strings, bytes, bytearrays, tuples, lists, sets, frozensets, dictionaries, and code objects (if allow_code is true), where it should be understood that tuples, lists, sets, frozensets and dictionaries are only supported as long as the values contained therein are themselves supported. The singletons None, Ellipsis and StopIteration can also be marshalled and unmarshalled. For format version lower than 3, recursive lists, sets and dictionaries cannot be written (see below).

There are functions that read/write files as well as functions operating on bytes-like objects.

The module defines these functions:

marshal.dump(value, file, version=version, /, *, allow_code=True)

Write the value on the open file. The value must be a supported type. The file must be a writeable binary file.

If the value has (or contains an object that has) an unsupported type, a ValueError exception is raised — but garbage data will also be written to the file. The object will not be properly read back by load(). Code objects are only supported if allow_code is true.

The version argument indicates the data format that dump should use (see below).

Raises an auditing event marshal.dumps with arguments value, version.

Changed in version 3.13: Added the allow_code parameter.

marshal.load(file, /, *, allow_code=True)

Read one value from the open file and return it. If no valid value is read (e.g. because the data has a different Python version’s incompatible marshal format), raise EOFError, ValueError or TypeError. Code objects are only supported if allow_code is true. The file must be a readable binary file.

Raises an auditing event marshal.load with no arguments.

Note

If an object containing an unsupported type was marshalled with dump(), load() will substitute None for the unmarshallable type.

Changed in version 3.10: This call used to raise a code.__new__ audit event for each code object. Now it raises a single marshal.load event for the entire load operation.

Changed in version 3.13: Added the allow_code parameter.

marshal.dumps(value, version=version, /, *, allow_code=True)

Return the bytes object that would be written to a file by dump(value, file). The value must be a supported type. Raise a ValueError exception if value has (or contains an object that has) an unsupported type. Code objects are only supported if allow_code is true.

The version argument indicates the data format that dumps should use (see below).

Raises an auditing event marshal.dumps with arguments value, version.

Changed in version 3.13: Added the allow_code parameter.

marshal.loads(bytes, /, *, allow_code=True)

Convert the bytes-like object to a value. If no valid value is found, raise EOFError, ValueError or TypeError. Code objects are only supported if allow_code is true. Extra bytes in the input are ignored.

Raises an auditing event marshal.loads with argument bytes.

Changed in version 3.10: This call used to raise a code.__new__ audit event for each code object. Now it raises a single marshal.loads event for the entire load operation.

Changed in version 3.13: Added the allow_code parameter.

In addition, the following constants are defined:

marshal.version

Indicates the format that the module uses. Version 0 is the historical format, version 1 shares interned strings and version 2 uses a binary format for floating point numbers. Version 3 adds support for object instancing and recursion. The current version is 4.

Footnotes